General
The Sonnox Transient Modulator functions by producing a continuous value that is proportional to the dynamic level encountered at its input (i.e. the programme level envelope). This value is then subjected to processing that extracts the rate of change of the programme level envelope, which is used to modify the forward gain of the output signal during the periods of dynamic activity in the programme. In this way the resulting level envelope at the output of the TransMod can be modified dramatically to accentuate or attenuate aspects of the dynamic profile of the sound, whilst drawing from the natural characteristics of the original programme signal.
Ratio Value
The ratio value represents the linear dB ratio by which the output gain will be modified by instantaneous changes in the input level. Positive values will increase the gain of the signal during transients. So for instance when the ratio control is set at +1, a drum attack that has a peak of 10dB above the average level will produce a level increase of twice that (20dB) at the output, because the gain during the transient will be increased by the same amount as its level difference.For negative ratios the reverse is true and for a negative ratio of -1 the drum attack transient would be reduced to the corresponding average level of the signal and therefore will be removed. In the central position (0) the TransMod process does not affect the signal at all.
Overshoot Value
The overshoot time sets the period over which the dynamic changes occur depending on the input programme dynamics. A short overshoot period will enhance (or reduce) transients for a very short time and cause only the leading edges of the transients to be modified. For instance a small overshoot time can accentuate short-term events in the programme such as small percussion – bells and the like whilst largely ignoring large and softer transients due to instruments such a drums etc.Increasing the overshoot period allows transient enhancement to occur over longer periods, therefore providing a method to tune the action to suit the programme material and produce the required effect.
The adaptive nature of the processing, over both level and time, allows optimal settings of the timing value can be achieved for complete tracks and even complex final mixes. Because the TransMod process is so rapid, low settings may not be heard because the duration of the transients being affected are too short. Generally the most audible effects occur from mid position upwards.
Recovery Value
The recovery value modifies the long-term timing of the envelope processing. Small recovery values will allow action to almost each and every transient, even if they repeated very rapidly in the programme material. Longer recovery values will gently and progressively reduce the action depending on the rate at which transients occur in the programme. So for instance, setting a long recovery value can prevent excessive action on small rapid transients in the signal (i.e. Hi-hat spill), which directly follow large transients (i.e. a Bass or Snare hit). The recovery time is adaptive such that after a period of absence for large transients, small transients in quieter sections of the programme will be progressively included once more into the process in the normal way. The effects of changing the recovery are usually quite subtle and for the most part small to midrange settings will work best for most popular material.Rise Time Value
The rise time value modifies the response of the envelope detector to fast transients and provides a method to decrease the sensitivity of the process to short term events in the programme. With the control set at minimum all transients, however short, will be processed. Increasing the rise time control reduces the overall speed of the envelope detector, such that short-term transients will be progressively ignored as they fall beneath the value of the rise time setting.The control can be used to prevent unwanted action from fast, largely inaudible transients, or it can be used as a sound effect. For instance, a rise time value can be arranged such that the initial attack of an instrument is excluded during an overall transient reduction or increase. This allows you to ‘model' the sound of the overshoot to soften or harden the effect.
Deadband Value
The dead band value provides a method to exclude less significant transient modifications from the final processing output. For instance, if a dead band of 3dBs is set, changes resulting from the TransMod processing below a total differential gain change of 3dBs are excluded from the process and the signal is unaffected during these conditions.The dead band control can be used to prevent action from small level changes or insignificant transients, which may otherwise adversely affect the programme. In this case it is best to start with the dead band set to zero and increase it only if unwanted action becomes evident, particularly during quiet sustained passages.
The dead band control may also be used to produce dramatic effects by focussing the TransMod action on to only the loudest transients in the programme. In this case it's best to set low thresholds and high ratios to get the maximum action, before progressively increasing the dead band to exclude smaller events from the effect.
Threshold Value
The threshold control causes the process to operate only on programme above the set level, ignoring all signals below that value. Unlike all the other processing in the plug-in, the threshold is related to absolute input levels and therefore care must be taken to set a low enough threshold value to allow action on the required range of programme.Careful threshold setting may be used to focus only on the louder events in the programme. This may be particularly useful when aiming for compression sounds with negative ratio settings. For generating increased attack with positive ratios, the TransMod process works most effectively when operating on the majority of the programme range, i.e. the lower the threshold the greater the possible effect may be.
Note: Care must be taken with very low threshold settings since programme starting from silence may be subjected to a large initial overshoot.
Level Control & Overdrive Settings
Although the TransMod process works to maintain constant average signal levels in the programme, the process can produce significantly larger peak levels if positive ratio values are used. In highly percussive sounds and long overshoot settings, the peak levels can potentially increase up to +24dB greater than in the original programme. This effect will be seen on the peak meters provided in the plug-in.Since most workstation applications provide no headroom above the peak level operating target that most users aim for, the extra transient information provided by the TransMod is highly susceptible to clipping in the application environment. If this occurs the transients are lost forever and cannot be recovered in the mix by level control further down line (i.e. faders etc). Therefore care must be taken to set appropriate gain settings to avoid clipping.
Overdrive Processing
The Overdrive process is included to allow a degree of relief from premature clipping if high modulation levels are required, by providing a method for the harmonic content of peak information above digital max to be included in the final output of the TransMod process.When set to maximum (100%) the overdrive process will allow peak information up to 6dB greater than max to be included without the sound of hard clipping, whilst avoiding digital overloads entirely. Overdrive processing will also change the harmonic content of the programme to provide warmth and richness to many programme types.
Loudness Enhancement
The TransMod when used with negative ratios can provide an efficient method to increase the loudness of programme by reducing very short transients that may otherwise cause overloads. In many cases very short transients may not be a prominent part of the programme sound and can be reduced without damaging the sonic character of the results. If very short-term peaks are reduced, more modulation gain can be achieved without overloads. Since look-ahead process timing can act on the signal before it appears at the output of the plug-in, short-term peaks can be effectively reduced without apparent loss of overall sonic character.To achieve this effectively, very small Overshoot and Recovery values should be used with a minimum Rise time setting, in order to catch the fastest transients only. A negative ratio coupled with a suitable dead band setting can be obtained that reduces transients by the required amount, allowing the overall level of the programme to be increased before limiting occurs.
Note: Since the TransMod is an adaptive process that constantly changes with programme content, the peak limiting function will not be as predictable and accurate as that provided by a programme limiter.